Ruched Ribbon Flower

Last week at my monthly quilting class, we were taught how to make ruched flowers.  They will eventually find their way onto yet another Christmas quilt that I have started (pictures coming soon…I hope!).  We made them with a strip of fabric, and because of possible fraying, had to do a few folds to hide any raw edges.  The whole time I was thinking I could definitely come up with a better, easier way to make these.  And of course, I was also sitting there wondering what else I could use them for.  It hit me last night.  Why not use ribbon?  No folding necessary since there are no raw edges to hide!  I played around with some pink and green ribbon, my two favorite colors, and that led me to the very large stash of pink and green papers that I have accumulated, and before I knew it, I had a cute card with a ruched ribbon flower embellishment.  (Don’t you love when you find a completely different purpose for your newly found favorite technique?)  Below you will find a tutorial on how to make the flowers.  Feel free to ask any questions, and if you can think of any other uses for these goodies, please share!

 

Enjoy,

 

Nikki, In Stitches

  

Materials:

36″ of 5/8″ wide ribbon

Needle

Coordinating embroidery floss (1 strand) or any heavy thread that will not break when pulling to ruche ribbon

*Note:  I used black embroidery floss in the pictures below so it would stand out.

  

Directions:

1.  Mark the wrong side of your ribbon, moving from right to left.  Along the bottom edge, mark every inch.  Along the top, first mark 1/2″ in, then mark every inch the rest of the way across.  If you’ve done this correctly, your marks should be evenly staggered the entire length of your ribbon, as shown in the picture provided.

 

2.  With a long piece of thread (approximately 36″), hand baste from mark to mark, creating a zigzag pattern, stopping occasionally to gather (“ruche”) the ribbon.  Stopping every eight to ten inches to gather your ribbon is recommended.  Any longer and you risk breaking your thread.  Also, put a hefty knot at the start of your thread so that as you pull to gather it doesn’t pull through your ribbon.

*The trick to the hand basting is to be consistent in your stitches.  If you look at the picture provided, I always do three stitches along each diagonal, and I was always sure to start by inserting the needle from underneath the ribbon and to end with the needle coming out the top.  I found this method made it easiest to gather the ribbon.

  

  

3.  Adjust your gathers so that your finished piece of ribbon is now ruched to about 17″.  Leave the long tail of thread in case any adjustments need to be made while assembling your flower.

 

 

4.  With a new piece of thread, baste across (from side to side) the first six “petals” of your flower.  Again, put a hefty knot at the start of your thread so you don’t pull it through when gathering.

  

  

 

 

5.  Pull the thread tight to form a circle of petals.  Knot the thread, but do not cut it, to hold the center loop of petals in place.

 

 

 

 

 

6.  Move gathered tail from the front of the flower to the back.  Use the before and after pictures provided below as a reference.

 

 

 

 

 

 

 

 

7.  Insert needle through the center of the flower to move the working thread from the front to the back.

 

 

 

 

 

 

 

 

8.  Spiral your gathered tail around and around, creating the layers of your flower.  Tack the flower together to keep the tail in place by coming up in the crease of each petal and back down in the same crease, being sure to catch the layer underneath.  The folds, or creases, in your petals will hide your stitches.

 

 

 

 

 

 

 

 

 

9.  Continue until you have tacked the entire tail in place.  Take a few extra stitches on the back of your flower to hold your ribbon end in place.  Knot and cut the working thread.

 

 

 

 

10.  Knot and cut the gathering thread.

 

 

 

 

 

 

 

11.  Embellish center with a button!